CaseJunkies.com - Los bericht bekijken

tribaloverkill · 20-05-2006, 21:48

Here's a cool update. You'll like this

Nov-18-2005

Here's another idea for an internal effect.

Nice long strips for the coil. I just got done cutting them off a larger sheet.

At first i tried my ruler-ruler method of cutting these guyz down but it only worked so much. Thers not enough material to be tape to the ruler, it wont stick. Need to do it another way.

I used the rulers as a fence and ran the strips through with the bit spinning towards the strips. If you do it with the bit spinning away,... it wil shatter them and spit them out the other side. No, this did not happen to me.

Holding up and flap made from a ruler,... it's used to hold down the strip while being cut. Was kind of nervous about having my wittle fingers that close to the bit. Didn't want to pull a Hobbes

Sorry Hobbes,... had to

Done. Now,...a mistake was made. Not really a mistkae but if I was smart I would of made both of these strips the same size. One os a spacer and the other is the actual coil. If I made them both the same size I would of had two coils

I still have to coils its just that one of them isnt the right size. Anyways. The coils can be stretched or compressed to adjust the gap before gluing too. You dont wan tot do that toooo much because its stressful on the holding arm thingies.

The cool part and painful. I got a pipe of the right diameter and sanded it clean. I then calculated the angle in hich to start wrapping and
I clamped the ends of the strips to the pipe side by side. I then began to heat and wrap. It was fairly easy. Very HOT. You should try and not stretch them out. You wan to pull firmly so its snug around the pipe but not to much. How cool is that

Trimmed and fitted. How friggin cool is that!!! HELL YEA. *HIGH FIVES MYSELF* Yea.

So yea. A nice preview for you guyz. I might update you guyz later. I'm off to the garage. Peace.

20-05-2006, 21:48	#10 (permalink)
tribaloverkill Geregistreerd: 18 mei 2006 Berichten: 420	Here's a cool update. You'll like this Nov-18-2005 Here's another idea for an internal effect. Nice long strips for the coil. I just got done cutting them off a larger sheet. At first i tried my ruler-ruler method of cutting these guyz down but it only worked so much. Thers not enough material to be tape to the ruler, it wont stick. Need to do it another way. I used the rulers as a fence and ran the strips through with the bit spinning towards the strips. If you do it with the bit spinning away,... it wil shatter them and spit them out the other side. No, this did not happen to me. Holding up and flap made from a ruler,... it's used to hold down the strip while being cut. Was kind of nervous about having my wittle fingers that close to the bit. Didn't want to pull a Hobbes Sorry Hobbes,... had to Done. Now,...a mistake was made. Not really a mistkae but if I was smart I would of made both of these strips the same size. One os a spacer and the other is the actual coil. If I made them both the same size I would of had two coils I still have to coils its just that one of them isnt the right size. Anyways. The coils can be stretched or compressed to adjust the gap before gluing too. You dont wan tot do that toooo much because its stressful on the holding arm thingies. The cool part and painful. I got a pipe of the right diameter and sanded it clean. I then calculated the angle in hich to start wrapping and I clamped the ends of the strips to the pipe side by side. I then began to heat and wrap. It was fairly easy. Very HOT. You should try and not stretch them out. You wan to pull firmly so its snug around the pipe but not to much. How cool is that Trimmed and fitted. How friggin cool is that!!! HELL YEA. HIGH FIVES MYSELF Yea. So yea. A nice preview for you guyz. I might update you guyz later. I'm off to the garage. Peace. __________________ iMod.